This weekend it is the turn of the Floorboards and floor bearers to get looked at and repair what needs repairing and then put back in Chance so we can work on the inside safely.

Sorting out a small area in my yard where I can sort the floorboards under cover and so they can dry out over the past few months.


The many problem with the floorboards was that they have been in Chance for such a long time without any chance to dry out and so became water logged ad so they were taken off Chance and brought to my yard and under cover and so they could dry out.


Now that Chance as a cover over her the floorboards in some parts of the boat can go back in position and help us be able to set up a small bench in the main cabin and a small galley area so we can keep ourselves warm with a brew during the time we are working on Chance inside as well as outside over the winter. 


Picking up the floor bearers we have got left when Chance was dismantled and see which can be reused and which can be repaired and what will need replacing so that the floor can go back down in the fore cabin galley and main cabin and the compainway from the aft cabin to the cockpit.


Starting to clean off years of paint and old fixing where they are still in the bits of floor bearers 


Some just need a cleaning and sanding back and a fresh coat of paint 



 

Comments

Post a Comment

Popular posts from this blog

A big shout out for a cover to put over Chance so we can get on with the restoration of Chance.

Image
 At the moment we are in this position with Chance, We have a large poly sheet over Chance which keeps getting blown off as we can not fix it down very well and is a thankless task having to keep pulling over the boat until the next major gale of strong wind decides to remove the cover again.  That's the position at the moment, what we are looking for is a shed/workshop like the one over Helen Wycherley Heritage Restoration project in Whitby North Yorkshire. This type of shed/ workshop would do our restoration project a world of good and make possible for us to get on with our restoration of Chance.    So if anyone out there can put us in contact with anyone who wishes to move on their poly tunnel shed/ workshop, please get in contact with us through our social media channels. This would help our restoration project get underway again. Te cost of building a new shed is way out of our price range and without some help it is looking in a grave way as to how to move for...
Read more

Chance Autumn update

As many of you will have seen from the lack of updates there as been little work done on Chance over the summer. This as been due a lack of time and more over a lack of funds to do major task done on Chance. especially the removal of the middle and aft section of the starboard beam shelf and reconstructing the transom and its framework which holds it in position.   However, all is not doom and gloom, has I have been able to take on an apprentice to help me during the working week on my clients boats and leave myself and wife time to get on with working on Chances repairs.  So hopefully over the coming week's we should be able to make a start on getting the beam shelf removed and replaced with a new correctly fitted beam shelf which will bring the hull back into position  along with the ribs and frames which have to be replaced at the same time to get the hull back into its correct position once more.  There is going to be a lot of shoring up of the starboard sid...
Read more

Next Job at the stern of Chance is going to be to remove the Rudder on Chance

Image
 Now having removed a number of planks on either side of the hog as found that the inner hog is in need of replacing. This means that we will have to remove the rudder tube. This means having to remove all the frame work from the transom to expose the rudder tube. The rudder tube in this photo is sitting on two shaped wedges on top of the hog.  Also all this aft deck planking is going to have to be removed as well. no easy job as it was laid down with galvanized screws which have been in place for almost 80 years and will very likely not come out without a lot of damage to the teak decking, so it is likely we will cut off the screws between the deck and the deck beams. This is not a problem as the deck beams have to be replaced anyway because at one end they are not fixed and at sometime in the past were cut short. So now the fun will start dismantling the aft end of the boat more to get the hog repaired and the whole of this area rebuild as strong as when it was first build....
Read more